Retro-fit Roof Support - ICID Plus

Features and Benefits

- Support arms can be installed during roof build = Chimney can be installed after roof build .

- Quick release toggle = Easy to remove.



Technical Data

Technical Data



Fuel
Wood, solid fuel | With Lip Seal: Gas and oil



Firing Temp
450 degreesC | With Lip Seal: 200 degreesC



Short Firing Temp
550 degreesC | With Lip Seal: 250 degreesC



Thermal Shock
1000 degreesC



Mode of Operation
Zero & negative pressure | With Lip Seal: Positive pressure



Pressure Capabilities
40Pa | With Lip Seal: 200pa



Fire Rating
4 Hour Fire Rating to BS 476 Part 20



Outer Case
Stainless Steel



Outer Case (Option)
Painted Matt black



Outer Case Thickness
0.5mm



Seam
Laser or inert gas welded



Liner
316L : 1.4404 : X2CrNiMo 17-12-2



Liner Thickness (mm)
0.5mm



Seam
Laser or inert gas welded



Insulation
High performance mineral fibre



Insulation Thickness
25mm



Average Thermal

Resistance (200 degreesC)
0.4m2 k/W





DimensionsThe dimensions of the flue are:


Int diameter mm
100
125
150
180
200



Ext diameter mm
150
180
200
235
256



Approvals
ICID Plus is CE Certified to EN1856-1 TUV 0036 CPR 9195 010 with designations:
ICID Plus is CE Certified to EN1856-2 TUV 0036 CPR 9195 042 with designations:
System Chimney EN1856-1
T450 N1 W V2 L50050 G60
T450 N1 D V3 L50050 G60
60mm Distance to combustibles in a combustible shaft*
T450 N1 W V2 L50050 G50
T450 N1 D V3 L50050 G50
50mm Distance to combustibles in a non-combustible shaft or in free air*
Zero distance to combustibles*
Connecting Flue Pipe EN1856-2
T450 N1 D V2 L50050 G100 M

Manufactured under a Quality Management Scheme approved to BS EN ISO 9001
4 Hour Fire Rating to BS476 Part 20
Certified for corrosion resistance on gas, oil and solid fuel by Gastec, MPA and TUV
HETAS listed for use on solid fuel applications.

Mandatory Requirements
Connection to an appliance which is not connected to the fuel supply, should be carried out by a competent person. We recommend the use of HETAS approved installers for solid fuel applications. If installation is carried out by a non HETAS registered installer, the installation must be certified by a local Building Control inspector. Connection to an appliance that is connected to the fuel supply must be carried out by a Gas Safe (Gas) or OFTEC (Oil) registered installer.
The design guide must be read in conjunction with the detailed component installation instructions. For full design and installation details the key referral documents are:

BS EN 1856-1: Chimneys - System Chimney Products
BS EN 1856-2: Connecting Flue Pipes
BS EN 1859: Metal Chimneys - Testing Methods
BS EN 1443: Chimneys - General Requirements
BS EN 15287-1: Chimneys. Design, installation and commissioning of chimneys. Chimneys for non-room sealed Heating appliances.
BS 5440-1: Fluing and ventilation for gas appliances of rated input not exceeding 70kW net (1st,

2nd and 3rd family gases). Specification for installation of gas appliances to chimneys and for maintenance of chimneys.

Approved Document J: - Combustion appliances and fuel storage systems (England & Wales)
DFP Technical Booklet L: - Combustion appliances and fuel storage systems (NI)
Technical Handbook (Domestic & Non Domestic), Section 3 - Environment (Scotland)
Appliance Installation Instructions and related standards. Other standards covering specific applications will also be relevant and must be adhered to.

Planning permission may be required, and reference should be made to the local Building Control Department.
Ensure all chimney components are available and check them to ensure there has been no damage. Do not use damaged components. Build the chimney up through the previous designed route which should be as straight as possible.